Removing the distributor ignition system

Removing the distributor ignition system
1. Disconnect the wire from the negative ¬ Noah battery terminals.
2. Disconnect the wires at high voltage on the cap ¬ valve (see "Checking the high-voltage wires").
3. Disconnect the connector of the distributor.
4. Removing the two hold-down bolts, remove (pull out) the distributor, then peel off the gasket from the body of the distributor. Note: Distributors Ignition Engine 4A-OE for mo ¬ Delhi AE92 with one hand and for the mo ¬ Delhi AT160 on theother hand, differ ¬ chayutsya slightly from each other, as well as the distributor of engines ¬ la 4A-FE (with lunch combustion system ¬ United seamstress). Therefore, the procedure of disassembly and assembly consider ¬ Xia together, especially in the case-
The distributor ignition system of ¬ (4A-FE system with lean burn). 1 - node cor ¬ Pusa valve assembly, 2 - rotor valve, 3 - ring seal ¬ tsevoe, 4 - cover distribution predelitelya.
The distributor ignition system of ¬ (4A-4A-CE and the PE system with CDF-Rania lean). 1 - pro ¬ water high voltage, 2 - ¬ predelitel races in the collection, 3 - O-ring seal, 4 - joint distribu ¬ shipment.
Stay one or another distributor - is given a special explanation.
Disassembly
Remove the cap and rotor distribu-Chairman (see "Details of the distributor").
Test
Turn the drive shaft distribu-Chairman, making sure that this is not observed in any ¬ seizure, no noticeable backlash. Otherwise, replace the valve body assembly.
The distributor ignition system of ¬ (4A-GE (AT160)). 1 - rotor distribution predelitelya ignition, 2 - housing ignition distributor assembly, 3 - wire clamp, 4 - cover distribution, predelitelya (with a high-wire, of stress), 5 - O-ring pack ¬ lotnenie, 6 - anther rotor races -, predelitelya, 7 - clamp the wire, 8 - Distributor duster, 9 - to-pin edinitelny led the sixth, thorns valve, 10 - led distributor drive gear, 11 - O-ring.
The distributor ignition system of ¬ (4A-GE (AE101)). 1 - node distribution predelitelya, 2 - O-ring seal ¬ nenie, 3 - rotor valve, 4 - valve cover.
"The distributor ignition system of ¬ (4A-FE (AE92)). 1 - rotor dis ¬ splitter plug, 2 - housing distribution predelitelya ignition assembly
3 - Cover the distributor (with pro-waters of the high voltage)
4 - O-ring, 5 - dust ¬ nick distributor rotor, 6 - anther valve, 7 - co-led the sixth pin edinitelny ¬ thorns distributor, 8 - Distributor driven gear drive, 9 - O-ring.
Replacing the distributor driven gear
(4A-0E)
1. Remove the driven gear, with a dish-sequence.
a) remove the grinding wheel saw off part of the connective ¬ pin, taking care not to damage the shaft of the centrifugal regulator ignition timing.
a) Remove the driven gear predelitelya distribution. 2. Install the new slave ¬ sixth turn, observing the sequence ¬ sion.
a) Remove the two bolts, remove the valve and gasket.
b) Install the driven gear on the distributor shaft (shaft centrifugal regulator ignition timing).
a) Align the groove on the crown wheel (not to be confused with a hole for the connecting pin) with ka ¬ Navka (AE92) or notch (AT160) on the body of the distributor, as shown, with protrusion of the distributor rotor should be in the position shown in Fig.
d) Install a new O-ring yn lotnenie and distributor cap and attach it with 2 screws.
Assembly
(4A-FE (with a combustion system lunch-ion mixtures))
1. Install the distributor rotor, pre-aligning the cavity on the rotor angular encoder pulses with a projection on the rotor ignition distributor.
Installation
1. Set the piston of the first cylinder at TDC ¬ Lindrum end of the compression stroke: a) (4A-DE)
Turn the crankshaft pulley and align the groove on the pulley with meth ¬ Coy "0" on the shell number 1 belt actuators ¬ Yes