Pipeline cloth

Pipeline cloth.
Disassembling the carburetor
(See "Details of the cover carburetor carburetor housing and housing Drosia ¬ selnyh dampers")
Note: if the sboroch-but-razborochno works, follow these guidelines.
a) To facilitate assembly, crucified ¬ lozhite details on a specific ¬ row.
b) Work together with a group sing ¬ parts belonging to only one assembly unit. This is in ¬ Zvolen avoid confusion between similar parts belonging to different assembly schimi ¬ ¬ unity Tsam (nodes).
c)Not to be confused and do not lose small parts (clamps, springs, balls and
etc.).
d) Use special devices (tools for karbyurato ¬ ditch).
Disassembling the carburetor cap
1. Remove the unit cover the carburetor.
a) Remove the adjusting bolt WHO ¬ duhoochistitelya.
b) Remove the fuel line clamp, fitting, fuel pipe and pro ¬ masonry unit for supplying fuel.
c) Disconnect the vacuum (e), hose (s).
e) Remove the thrust of the drive excitation ¬ air damper.
e) (Models for Research of Germany with a 3-component neutral ¬ jam exhaust)
Remove the thrust mechanism of opening the choke.
g) Remove the following (removing the 8 screws).
• Number Plates;
• Anchor fuel tube console (the model for Europe);
• wire clamps for air ¬ slonki and solenoid valve off the fuel supply.
h) Remove the carburetor with gasket.
i) Disconnect the wires), electro ¬ magnetic valve off the fuel supply.
k) (Models for Research in Germany ¬ 3-component neutral jam-exhaust) Disconnect wire connector from the positive gravitational ¬ throttle switch, as shown in the figure.
2. Remove the float and needle valve of the fuel supply.
a) Remove the axle float, then float and needle valve assembly.
b) Remove the cover gasket car-byuratora.
a) Remove the needle seat from the valve gasket.
3. Remove the stem and the economizer pru ¬ Jin, having removed the lock. Remove the plunger on the accelerator ¬ Sosa, having removed the protective cover.
5. Remove the plate and the axis of the choke.
Note: to carry out this proce-fool only if there is a need to replace the air-tion axis of the damper or the switch on Proposition ¬ choke.
a) removing the 3 screws, remove the thermostat housing.
b) Remove the thrust of the choke switch and remove the diaphragm switch.
d) removing the screw, remove the control arm increased speed of idling.
c) removing the screw axis of the air ¬ slonki, remove the lever for ¬ slonki, "discharge" (unlock-vochny) lever and washer.
e) saw off the ends of the sawn wafer mounting screws possibility ¬ air damper, remove them and clear the air over the plate ¬ slonki.
e) Remove the reference fuel ¬ voprovoda console.
Disassembling the carburetor body
1. Remove the solenoid (e), cluster ¬ pany) off the fuel supply.
2. Remove the back (small) sha ¬ rikovy valve accelerator pump.
a) Remove the locking gaskets-ku, discharge (gravitational ny) valve spring length and
ball (large) Discharge the accelerator pump.
b) Remove the damper (pre-analyzing systems and safety) spring accelera ¬ relatively pump.
c) Using tweezers, remove the lock plunger accelerator pump and the ball (small) inverse ¬ Nogo valve.
3. (Models for Europe) Remove the positioner (manipulator, "positioner") choke ¬ Noah damper disconnect traction mani ¬ pulyatora and by removing the 2 screws, remove the handle.
5. Remove (with pads), small cones of primary and of secondary chambers.
6. Remove the sight glass Poplav ¬ kovoy chamber and its sealing ring, having removed the holding ¬ Tel glass.
7. Remove the cam control unit high-speed ho-cavity by heating of the engine.
a) Remove the recoil spring and snatch control lever increase shennoy ¬ ¬ idle speed of travel.
b) Remove: fixing bolt, washer, cam and lever increase shennoy ¬ ¬ idle speed of travel, washer lever.
9. (Only for GP appoint ¬ radiation without heating system air intake)
Remove the thermostatic valve: remove the 3 screws and remove the cover termoklapa ¬ on, cover gasket, thermostatic valve and thermo-sealing ring.
10. (Models for Research in Germany ¬ 3 ¬ torus component neutralization of exhaust) Remove the throttle position switch with poles ¬ Noah console, pre ¬ nuv Hole 2 screws.
11. Separate the shell of the carburetor throttle body ("flange" carb.) a) Remove the three screws holding the carb body to the flange and screw vacuum channel (2).
b) Keep the body of the carburetor flange.
a) Remove the washer from the primary axis of the throttle
d) Remove: adjustment screw on the mixture composition ¬ idle ("mixture screw") and the regulation screw ¬ ki speed to normal idle mode ("screw number").
Carburetor cleaning technology
Clean the disassembled elements of the car ¬ byuratora to check.
a) Wash and clean the cast parts with a soft brush and carburetor fluid ¬ Coy wash.
b) Remove carbon from the remains of the throttle.
c) Rinse the remaining parts of liquid ¬ Coy wash.
d) Purge the channels and orifices car ¬ byuratora.