Check carburetor

Check carburetor
1 - Check the float needle valve and fuel supply.
a) Evaluate the float axle wear and scratches.
b) Assess the elements of the float, making a lack-dance breakdowns push the tongue-in melting and wear a hole under the axle.
c) Assess the spring, making sure no damage and deformities.
d) Assess damage and wear elements ¬ ments needle valve: ¬ locking element and the plunger.
e) Check the strainer for contamination and integrity.
2. Check the operation of the piston ekonomay¬ laser, making sure that it moves freely ¬ free.
3. Check valve Efficiencies, making sure it performs the function-tion locking in the closed position and the transmission function in the open position, as shown in the figure.
c) Replace the O-ring. 5. (Models for Germany with a 3-component neytralizato ¬ rum exhaust) Check the position switch throttle. Connect one ohmmeter probe to the terminal switch, and another - to his body. Make sure that you are not depressed stock switch contacts are closed (ohmmeter will show a short circuit), and when you press the switch contacts open stock (ohmmeter shows infinite).
6. Check the heater coil choke, measured with the aid of an ohmmeter aid of an electric ¬ ¬ tance resistance between the terminals and housing heater.
The magnitude of the resistance at a temperature of 20C ¬ tem. 20-22 ohms
If the resistance is outside the UCA-zannye limits, replace the heater coil.
Carburetor assembly
(See figure "Details Cover karbyura ¬ torus, housing and the carburetor throttle body") Note: The commonly used ¬ are the new O-rings.
Assembling the carburettor body
1. Connect the carburetor housing and the throttle body ("flange" carb.)
a) Install the adjusting screw for rotational frequencies h ¬ ¬ rick normal holo-way (screw "number") and the adjustment screw of the mixture at normal idling mode (screw the "quality").
b) Place a washer on the axle Drosia ¬ selnyh dampers.
2. (Models for Germany with a 3-component neytralizato ¬ rum exhaust) Set circuit breakers position ¬ Tel throttle with the support console and attach it with 2 screws.
3. (Only for GP appoint ¬ radiation without heating system air intake)
Install thermostatic valve and thermo-cap (with a new gasket), securing it with 3 screws.
a) Connect the thrust diaphragm mechanism with a lever actuator of secondary throttle. 5. Install the cam control in no-load speed vyshennoy ¬ th move.
a) Install the snatch and return ¬ nuyu spring lever increased speed of the ho ¬ cavity.
b) Place: puck control lever of high ¬ speed of idling, even the washer, the cam washer and a bolt.
6. Install a new O-ring, float glass viewing chamber ¬ howl and the sight glass holder.
7. Set small diffusers per ¬ tion of primary and secondary chambers carburetor.
b) Install the spring, washer, market-fungus throttle affix their beers ¬ nut with spring washer.
9. (Models for Europe and Singapore)
Install the positioner (manipulator, "positioner") Drosia selnoy-flap, securing it with 2 screws. Attach the thrust manipulation ¬ oscillator.
10. Set the electromagnetic (e) valve (s) off fuel supply ¬ va, pre-installing new gaskets on the mounting (s), place (s) on the body carburetor.
11. Install the accelerator pump ball valves.
a) Install the ball (large) on-line gnetatelnoy accelerator pump, a long spring, forcing ¬ negative (gravitational) and valve plug.
b) Using tweezers, set the lock plunger accelerator pump and the ball (small) back ¬ of the valve.
a) Install a damper (pre ¬ analyzing systems and safety) spring accelerator ¬ relatively pump.
b) Set the axis for air-air plate slonki and over-slonki fixing the last screw ¬ mi. Saw off the ends of the screws.
a) Set the control lever in vyshennoy speed holo ¬ rick course, securing it with a screw.
d) Set: puck, "Water & Lube Oil-unloading" (unlock) the choke, choke lever, securing them with a screw.